Products / Superbolt
Superbolt · mechanical tensioners

Superbolt tensioners.
Tension you can trust, with a hand wrench.

Multi-jackbolt tensioners replace the hex nut on the joints that cannot leak. No hammer wrench, no hydraulic torque, no hot work. Supplied and installed by GIMAN in Mexico and the United States.

How it works

Many small bolts do the jobof one huge bolt

A Superbolt tensioner threads onto the existing stud in place of the hex nut. Instead of turning one large nut against friction, you tighten a ring of small jackbolts.

  1. Spin it on by handA direct replacement for the hex nut, on the stud you already have.
  2. Tighten the jackboltsEach one needs little torque. Together they push against a hardened washer.
  3. The stud is in pure tensionNo torsion and no thread galling. The load is even around the whole bolt circle.
  4. Take it off the same wayHand tools only, outage after outage. The tensioner is reusable.
Animation: assembly and tightening of a Superbolt tensioner
Superbolt in cross-section
Superbolt in cross-section
Jackbolts tightened with a hand wrench
Jackbolts tightened with a hand wrench

Hammer wrench or hydraulic torque

  • About 90 % of the torque is lost to friction
  • Preload error of ±30–40 % or more
  • Compressor, pump, hoses and wrench: each one can fail
  • Three people, heavy gear, impact injuries
  • Leaks and re-tightening at start-up

Superbolt

  • Pure tension on the stud
  • Preload accuracy of ±5–10 %
  • One hand torque wrench
  • One person, in confined spaces
  • Leak-tight from the first pass

Friction and accuracy figures published by Nord-Lock Group, maker of Superbolt.

Torque is not tension. Tension is what seals the joint.

Case · PEMEX offshore

From 72 hours to 25on a compression module in the Bay of Campeche

In the Bay of Campeche, flanges from 2 to 36 inches were bolted at night, in tight spaces, with hammer wrenches and hydraulic torque. Every leak at start-up meant re-tightening and deferred production. This is what changed when we switched to Superbolt.

Before: a full crew on one hammer wrench
Before: hydraulic torque, pump, hoses and wrench

The trial: on and off with a hand wrench, on the same flange

Superbolt: tightening with a hand wrench
Superbolt: loosening with the same hand wrench
77 %less time removing and fitting studs on a 24-inch, class 150 flange
0 hof leak re-tightening. The previous method needed 10 hours and three re-tightenings
3 → 1people needed to tighten the joint

Our own measurements on the platform (POL-A process centre, June 2018), against hydraulic torque on the same flange.

Abkatún-A, December 2019: installation with our own crew on board

We installed Superbolt on the compression-module joints with a torque audit of every tensioner.

JointSize
Flanging module36″ · 600#
V-101 manway30″ · 300#
V-101 inlet and outlet24″ · 300#
Retention cones, module 124″ · 150# and 14″ · 300#
PSV, fuel gas, drains and spools2″–8″ · 150–300#
25 hinstead of 72 h on the retention cones and blinds of one module
47 hearlier module start-up at every maintenance
V-101 24-inch outlet with Superbolt · Abkatún-A
V-101 24-inch outlet with Superbolt · Abkatún-A
Superbolt on a platform flange
Superbolt on a platform flange
Working over the side of the platform
Working over the side of the platform

Zero leaks. Zero re-tightening. Two days back at every start-up.

Turbines

Superbolt on gas and steam turbinesno bolt heaters, no hammer wrenches

  • Casings and horizontal joints. Even tension, no bolt heating, no hammer wrench.
  • Couplings (expansion bolts). They go in and come out without seizing. Installed on a steam turbine in Baytown, Texas, in 2025.
  • Boiler feed pumps. Tensioners supplied to CFE Carbón II under two contracts, 2022 and 2023.
  • Steam valves and piping. Inlet flanges and admission valves.
  • From the factory. The GE D11 and the Siemens 501F ship with Superbolt by design; on the 501F 4-way joint they take the load from the hydraulic closure. See the 4-way joint
Steam turbine inlet flange
Steam turbine inlet flange
Steam turbine split-case joint
Steam turbine split-case joint
Where tensioners go on a gas turbine frame (Nord-Lock Group)
Superbolt on a turbine joint
Superbolt on a turbine joint
Jackbolt tightening on a turbine casing
Jackbolt tightening on a turbine casing
Where it is used

The joints that cannot leakand the places a hydraulic wrench does not fit

WhereWhy Superbolt
Offshore flanges and compression modulesHand wrench at night and in tight spaces; leak-tight from the first pass
Blowout preventers: stack flanges, ram bonnets, choke and kill linesEven load on the metal ring gasket; several technicians tighten at once
Wind: main shaft, hub, gearbox, tower flangesCarry a wrench up the tower, not a pump
Mud pumps, top drive, drawworksHolds preload under vibration; pairs with Nord-Lock washers
Mining and steel: crushers, mills, pressesLarge diameters tightened with hand tools

BOP and wind: application examples from Nord-Lock Group.

Superbolt in English · GIMAN channel
Superbolt in English · GIMAN channel
Superbolt · GIMAN channel
Superbolt · GIMAN channel

Carry a wrench, not a pump

Nothing heavy to lift up a tower or to a platform deck.

Seals first time

Even load on the gasket, so the pressure test passes without re-tightening.

Traceable

A torque audit of every tensioner, recorded for the joint file.

Full case, BOP and wind chapters and downloads: info.giman.com/bolting ↗ · Nord-Lock · Boltight

Questions

About Superboltbefore you quote

What is a Superbolt tensioner?

A multi-jackbolt tensioner (MJT) that threads onto the existing stud in place of the hex nut. Instead of turning one large nut against friction, you tighten a ring of small jackbolts with a hand torque wrench; together they push against a hardened washer and leave the stud in pure tension.

Do I need to change the studs?

Usually not. Superbolt is a direct replacement for the hex nut on the stud you already have. We check thread, length and clearance from your drawings before quoting.

How accurate is the preload?

About ±5–10 % with Superbolt, against ±30–40 % or more with a hammer wrench or hydraulic torque, where about 90 % of the torque is lost to friction (figures published by Nord-Lock Group).

Is it reusable?

Yes. It comes off with the same hand wrench, outage after outage.

Do you supply Superbolt in Mexico?

Yes. We supply Superbolt tensioners and Nord-Lock washers in Mexico and the United States, and our crews install them with a torque audit of every tensioner when you need it. We work as a field execution channel for Nord-Lock Group.

Quote

Tell us the joint: diameter, thread and class

Send the bolt size, flange class or equipment and the quantity. We size the tensioner, check clearance and tell you if it fits your stud.

  • Supply in Mexico and the U.S.
  • Installation with torque audit

info@giman.com · +1 832 408 9841 (WhatsApp)
Cleveland, Texas · Mexico · Canada

¡Contáctanos!