Hydraulic nuts and casing bolt tensioners for the Frame 7E / 7EA horizontal joint, with air-driven pump, hoses and manifolds, rented from Cleveland, TX. Our own TFAs install and run the tooling during combustion, hot-gas-path and major inspections on peakers, cogen and older combined-cycle units.

Many 7EA operators still open and close the casing by heating or torquing each horizontal-joint bolt. Hydraulic nuts and tensioners load several studs at once from a single pump and release with pressure, so bolting and unbolting the joint takes a fraction of the time and every stud receives the same preload.
GIMAN Energy rents the tooling and sends its own TFAs. Some 7EA casings have areas where tooling can clash with the casing: we review your unit's drawings and bolt schedule before mobilization and confirm fit with the manufacturer.

| Hydraulic tooling | Hydraulic nuts and casing tensioners sized to the 7E/7EA stud schedule; confirm your unit's sizes with the RFQ |
|---|---|
| Pump & hoses | Air-driven pump, link hoses, tee blocks and manifolds for parallel tensioning |
| Accessories | Sockets, adaptors, operating manual and calibration records |
| Transport | Custom case; shipped from Cleveland, TX; temporary import for Canada and Mexico |
| Service | Optional GIMAN TFAs: pre-job fit review, installation, sequenced tensioning, verification and report |


You bring the unit and the outage window. We show up with the kit and the TFAs.
You send unit, frame revision and outage window. We confirm kit availability, match nut sizes to your bolt schedule and ship from Cleveland, TX.
Our TFAs run the site induction, verify the tooling against the casing and set up pump, manifolds and hoses per the manufacturer procedure.
Hydraulic load is applied in sequence and monitored on gauges. Readings and any deviations are recorded with your outage team.
Tooling is inspected, packed and returned. You receive the field service report and calibration records for your outage file.
Based in Cleveland, TX. Registered on GE Vernova / FieldCore's SAP Business Network and prequalified in ComplyWorks (score 98, Severe class).
Part of the 26 4-way joint installs delivered on the North American 501F fleet in 2025–2026 took place in Canada.
Bilingual crews (EN/ES). Quotes in USD; temporary import coordinated with your customs broker or importer of record, project by project.
Calibrated tooling, the manufacturer's procedure. And an as-found / as-left report when we're done.
They tension several studs at once from a single pump and release with pressure, so bolting and unbolting the horizontal joint takes a fraction of the time of heating or torquing each bolt.
Most units yes; some 7EA casings have areas where tooling clashes with the casing. GIMAN reviews your unit's drawings before mobilizing.
It can be. GIMAN's own TFAs install, run and remove the kit on site, or the kit ships to your crew with the manufacturer procedure.
Yes, with a separate kit sized to the 7F stud range. See the GE 7FA casing tool rental page.
The Frame 7E / 7EA horizontal joint on peakers, cogeneration and older combined-cycle units, during combustion, hot-gas-path and major inspections.
Hydraulic nuts and casing tensioners sized to the 7E/7EA stud schedule, an air-driven pump, link hoses, tee blocks and manifolds for parallel tensioning, sockets, adaptors, an operating manual and calibration records, in a custom case shipped from Cleveland, TX.
The kit for your frame (hydraulic nuts or tensioners, hoses, pump, manifolds, gauges and adaptors), the manufacturer procedure, calibration records and, if you choose it, our own TFAs to install, operate and remove the tooling.
By project: kit rental, TFA days, mobilization and consumables as separate line items on the RFQ. Rate card on request. NDA available; POs through SAP Business Network or directly.
Yes. Our scope is the hydraulic tooling and its operation; cover lift, rigging and overall outage coordination stay with your prime. We align the sequence with your outage manager before mobilization.
Yes. Canada and Mexico / Latin America are quoted per project in USD, with temporary import handled together with your customs broker or importer of record.
Send us the unit, frame revision, bolt schedule and outage window. We come back with availability and a project quote.
26724 Morgan Cemetery Rd, Office Warehouse Bldg #3
Cleveland, TX 77328, USA
GIMAN GROUP GM
Monterrey, N.L., Mexico (service area)
Phone / WhatsApp: +1 832 408 9841
Email: info@giman.com
GIMAN Energy LLC is an independent company that rents and operates Boltight® hydraulic closure and tensioning tooling and executes installations as a channel for Nord-Lock® / Superbolt® solutions. Boltight, Nord-Lock and Superbolt are trademarks of their owners within Nord-Lock Group. GE, 7FA, 7EA, D11, Siemens and Westinghouse are trademarks of their respective owners and are used for identification of turbine frames only.